Hyundai Santa Fe: Hydraulic System / SS-A Solenoid Valve (ON/OFF). Repair procedures

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Automatic Transaxle System (SBC) / Hydraulic System / SS-A Solenoid Valve (ON/OFF). Repair procedures

Inspection
  
Refer to the DTC manual for the check procedure.
Removal
  
Be careful not to damage the parts located under the vehicle (floor under cover, fuel filter, fuel tank and canister) when raising the vehicle using the lift.
(Refer to General Information - "Lift and Support Points")
When the solenoid valve Diagnostic Trouble Codes (DTC) is on, perform the following procedure to replace it.
Automatic transaxle is composed of delicate components. Be careful not to cause any damage on the component in the course of assembly and disassembly.
Maintain clean condition so that foreign substance does not get into the automatic transaxle.
Use a coated apron, latex gloves, and stainless tray to prevent foreign substance from getting into the transaxle.
Automatic transaxle fluid (ATF) can be reused. Collect it using a clean 10-liter beaker.
1.
Turn ignition switch OFF and disconnect the negative (-) battery cable.
2.
Remove the air duct and the air cleaner assembly.
(Refer to Engine Mechanical System - "Air Cleaner")
3.
Separate the air bleed hose (B) and then wiring bracket (A).

4.
Remove the under cover.
(Refer to Engine Mechanical System - "Engine Room Under Cover")
5.
Remove the drain plug (A) and reinstall the drain plug after draining ATF totally.
Drain plug tightening torque :
33.3 - 43.1 N.m (3.4 - 4.4 kgf.m, 24.6 - 31.8 lb-ft)

  
Replace the gasket before reinstalling the drain plug.
6.
Loosen the mounting bolts (A) of the valve body cover.
Tightening torque :
11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

  
Be careful when removing the valve body cover because the remaining ATF remains in the valve body cover.
  
Replace the gasket (A) before reinstalling the valve body cover.
After the installation, start the engine and then check if there are any leakages from the valve body cover.

7.
Loosen the bolts and then removing the main harness (A).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb-ft)

8.
Loosen the support bracket mounting bolts (A).
Tightening torque :
9.8 - 11.8 N.m (1.0 - 1.2 kgf·m, 7.2 - 8.7 lb-ft)

9.
Remove the support bracket (A).

10.
Remove the ON/OFF solenoid valve (A).

Installation
1.
To install, reverse the removal procedure.
2.
Inject the automatic transaxle oil and inspect the oil level.
(Refer to Automatic Transaxle System - "Automatic Transaxle Fluid")
  
After ATF level check or exchange, be sure to remove residual ATF on transaxle case.
(Be especially sure to remove residual ATF between automatic transaxle case and valve body cover)
After installing the valve body cover, make sure to check the oil leakage at the connection area with the engine ON.
3.
Clear the diagnostic trouble codes (DTC) using the diagnostic tool.
(Refer to Automatic Transaxle System - "Automatic Transaxle")
  
Even though disconnecting the battery negative terminal, the DTCs will not be cleared. So, be sure to clear the DTCs using the diagnostic tool.
4.
In order to prevent start delay and gear shift shock during acceleration and start, perform TCM learning after replacing the solenoid valve.
(Automatic Transaxle Control System - "Repair Procedures")

    SS-A Solenoid Valve (ON/OFF). Specifications

    Specifications ▷ Control type : Normally low type Shape Items Specifications Control voltage [V] 9 - 16 Supply pressure [kpa (kgf/cm², psi)] 490...

    Automatic Transaxle Cooling System

    ..

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Power Door Lock Actuators. Repair procedures


    Inspection Front Door Lock Module Inspection 1. Remove the front door trim. (Refer to Body - "Front Door Trim") 2. Remove the front door module. (Refer to Body - "Front Door Module") 3...

    Hyundai Santa Fe (TM) 2019-2024 Owner's Manual: SRS care


    The SRS is virtually maintenance-free and there are no parts you can safely service by yourself. If the SRS air bag warning light does not illuminate when the Engine Start/Stop button is in the ON position, or continuously remains on, have the system be immediately inspected by an authorized HYUNDAI dealer...

    Categories

    Power adjustment

    The front seat can be adjusted by using the control switches located on the outside of the seat cushion. Before driving, adjust the seat to the proper position so that you can easily control the steering wheel, foot pedals and controls on the instrument panel.

    WARNING

    NEVER allow children in the vehicle unattended. The power seats are operable when the vehicle is turned off.

    read more


     
    Copyright © 2024 www.hsafe4.com