Hyundai Santa Fe: Front Door / Front Door Module. Repair procedures

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Body (Interior and Exterior) / Front Door / Front Door Module. Repair procedures

Replacement

1.	Remove the front door window glass. (Refer to Front Door - "Front Door Window Glass")

2.	Remove the front door outside handle. (Refer to Front Door - "Front Door Outside Handle")

3.	Remove the front door speaker. (Refer to Body electrical system - "Speaker")

4.	Loosen the lock pin and separate the front door main connector (A).

5.	Loosen the front door outside handle screw (A).

6.	Using a screwdriver or remover, remove the outside rear view mirror inner cover (A).

7.	Press the lock pin, separate the outside rear view mirror connector (A).

Loosen the front door latch screws (A).

Tightening torque :

7.8 - 10.8 N.m (0.8 - 1.1 kgf.m, 5.8 - 8.0 lb-ft)

Loosen the front door moodule bolts and remove the front door module (A).

Tightening torque :

7.8 - 11.8 N.m (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)

10.	Disconnect the various connector fron the front door module and separate the front door module wiring harness (A).

11.	Remove the front door latch assembly. (Refer to Front Door - "Front Door Latch Assembly")

12.	Remove the front power window motor. (Refer to Body Electrical System - "Power Window Motor")

13.	Remove the impact sensor. (Refer To Airbag System - "Side Impact Sensor")

14.

To install, reverse removal procedure.

•	Make sure connectors are connected properly and each rod is connected securely.

•	Make sure the door locks / unlocks and opens / closes properly.

Front Door Module. Components and components location

Front Door Outside Handle. Components and components location

Other information:

Hyundai Santa Fe (TM) 2019-2024 Service Manual: Description and operation

Description Body Control Module Controls The Followings – Wiper & Washer Control – Defroster Control – Driving Control – Tailgate Control – Window Control – Interior Control – Exterior Control – Panic alarm Control – MTS – Flasher output Control – Door lock/unlock Control – Burglar alarm Control – Remote start Control – UMS(User Mode Setting) Control – Gateway/ Diagnosis Integrated Body Control Unit (IBU) Integrated body control unit has integrated several functions including body control module (IBU), smart key unit (SMK), and tire pressure monitoring system (TPMS)...

Hyundai Santa Fe (TM) 2019-2024 Service Manual: Transaxle Control Module (TCM). Schematic diagrams

TCM Connector and Terminal Function TCM Terminal Function Connector [A] Pin No Description Connected to 1 Power ground Chassis Ground 2 - - 3 - - 4 - - 5 - - 6 Fuel Sender Signal Fuel Sender 7 - - 8 - - 9 - - 10 - - 11 - - 12 - - 13 - - 14 - - 15 Stop Lamp Signal Stop Lamp 16 Brake Test Switch Brake Switch 17 18 - 19 - 20 Output Speed (Supply) ATM Solenoid Valve (Otput Speed) 21 Input Speed (Supply) ATM Solenoid Valve (Input Speed) 22 - - 23 - - 24 - - 25 - - 26 - - 27 [A/T] SOL...

Categories

Air bag collision sensors

WARNING

To reduce the risk of an air bag deploying unexpectedly and causing serious injury or death:

Do not hit or allow any objects to impact the locations where air bags or sensors are installed. Do not perform maintenance on or around the air bag sensors. If the location or angle of the sensors is altered, the air bags may deploy when they should not or may not deploy when they should. Installing bumper guards with nongenuine Hyundai or non-equivalent parts may adversely affect the collision and airbag deployment performance. Press the Engine Start/Stop button to the OFF or ACC position and wait for 3 minutes when the vehicle is being towed to prevent inadvertent air bag deployment. Have all air bag repairs performed by an authorized HYUNDAI dealer.