Hyundai Santa Fe: Windshield Wiper/Washer / Front Wiper Motor. Repair procedures

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Body Electrical System / Windshield Wiper/Washer / Front Wiper Motor. Repair procedures

Removal
1.
Disconnect the negative (-) battery terminal.
2.
If necessary, release the wiper blade fixing clip(A) by pulling up and remove the wiper blade(B) from the inside radius of wiper arm.
3.
Remove the cowl top cover.
(Refer to Body - "Cowl Top Cover")
4.
Disconnect the wiper motor connector (A) from the wiper motor & linkage assembly.
5.
Remove the windshield wiper motor and linkage assembly (A) after removing 2 bolts.
6.
Hold the wiper motor crank arm and remove the upper linkage (A) from the wiper motor crank arm.

  
Before removing the wiper motor and linkage assembly, make sure that the linkage is stoped at auto stop position.
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Be careful not to bend the linkage.
7.
Remove the lower linkage (A) from the wiper motor crank arm.

  
To install the wiper motor crank arm exactly, check that the linkage is aligned with the crank arm in straight line and the angle of each linkages.
Be careful not to bend the linkage.
8.
Remove the crank arm (B) after loosening a nut (A).
9.
Remove the bracket (A) after loosening the screws (3EA).
10.
Remove the wiper motor from the tube.
Installation
1.
Install the wiper motor and linkage assembly and then connect the wiper motor connector.
Tightening torque:
6.9 - 10.8 Nm (0.7 - 1.1 kgf.m, 5.0 - 7.9 lbf.ft)
2.
Install the cowl top cover.
3.
Install the windshield wiper arm and blade.
Tightening torque:
22.5 - 26.5 Nm (2.3 - 2.7 kgf.m, 16.6 - 19.5 lbf.ft)
  
–
The windshield wiper motor must be cycled to make sure that it is in the park position.
If necessary, adjust the wiper arm and blade.
4.
Install the wiper arm and blade to the specified position.
A: Auto stop position (Blade)
Inspection
Speed Operation Check
1.
Remove the connector (A) from the wiper motor.
2.
Attach the positive (+) lead from the battery to terminal 3 and the negative (-) lead to terminal 1.
3.
Check that the motor operates at low or high speed as below table.

  
Common sources of contamination are insects, tree sap, and hot wax treatments used by some commercial car washes. If the blades are not wiping properly, clean both the window and the blades with a good cleaner or mild detergent, and rinse thoroughly with clean water.
Diagnosis with diagnostic tool
1.
In the body electrical system, failure can be quickly diagnosed by using the vehicle diagnostic system (diagnostic tool).
The diagnostic system (diagnostic tool) provides the following information.
(1)
Fault Code Searching : Checking failure and code number (DTC)
(2)
Data Analysis : Checking the system input/output data state
(3)
Actuation test : Checking the system operation condition
(4)
S/W Management : Controlling other features including system option setting and zero point adjustment
2.
If diagnose the vehicle by diagnostic tool, select "DTC Analysis" and "Vehicle".
3.
Select the 'Data Analysis'.
4.
Select the 'IBU_BCM' to search the current state of the input/output data.

    Front Wiper Motor. Components and components location

    Component Location 1. Cap 2. Nut 3. Wiper arm & blade 4. Cowl top cover 5. Bolt 6. Wiper motor & linkage assembly 7...

    Front Washer Motor. Repair procedures

    Inspection Front and Rear Washer Motor 1. With the washer motor connected to the reservoir tank, fill the reservoir tank with water...

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Specifications


    Specifications [ADAS_PRK Application Specification (MOBIS)] Item Specification Ultrasonic sensor Voltage rating DC 12V Detecting range 40cm ~ 120cm Operating voltage DC 9V ~ 16V Operation current MAX...

    Hyundai Santa Fe (TM) 2019-2024 Owner's Manual: Lane Keeping Assist (LKA)


    Lane Keeping Assist is designed to help detect lane markings (or road edges) while driving over a certain speed. The system will warn the driver if the vehicle leaves the lane without using the turn signal, or will automatically assist the driver’s steering to help prevent the vehicle from departing the lane...

    Categories

    Air bag collision sensors

    WARNING

    To reduce the risk of an air bag deploying unexpectedly and causing serious injury or death:

    Do not hit or allow any objects to impact the locations where air bags or sensors are installed. Do not perform maintenance on or around the air bag sensors. If the location or angle of the sensors is altered, the air bags may deploy when they should not or may not deploy when they should. Installing bumper guards with nongenuine Hyundai or non-equivalent parts may adversely affect the collision and airbag deployment performance. Press the Engine Start/Stop button to the OFF or ACC position and wait for 3 minutes when the vehicle is being towed to prevent inadvertent air bag deployment. Have all air bag repairs performed by an authorized HYUNDAI dealer.

    read more


     
    Copyright © 2024 www.hsafe4.com