Hyundai Santa Fe: Smart Key System / Smart Key Unit. Components and components location
Hyundai Santa Fe (TM) 2019-2024 Service Manual / Body Electrical System / Smart Key System / Smart Key Unit. Components and components location
| Components (1) |
Connector Pin Information
|
No |
Connector A |
Connector B |
Connector C |
|
1 |
Fuel door release switch_input |
GND_ECU |
Front wiper relay (Low)_output |
|
2 |
Fuel door open switch_input |
PDW-F power_output |
ESCL (+)_output |
|
3 |
GND_Power |
ESCL (-)_output |
Start relay_output |
|
4 |
PDW-R_Power_Output |
Front wiper high relay_output |
IGN1 relay_output |
|
5 |
EMS ECU wake up_output |
PDW-R switch IND_output |
Immobilizer antenna power_output |
|
6 |
Rear washer switch_input |
P-Position_input |
Immobilizer antenna ground_output |
|
7 |
LIN4 (Rear seat remind) |
- |
- |
|
8 |
P_CAN (Low) |
Rear view switch_input |
Driver outside handle antenna(+)_output |
|
9 |
P_CAN (High) |
- |
Interior1 antenna (+)_output |
|
10 |
- |
Wheel speed sensor_input |
Front bumper antenna (+)_output |
|
11 |
B_CAN (Low) |
- |
Tailgate3 antenna(+) |
|
12 |
B_CAN (High) |
3rd line sheet belt indicator RH_output |
- |
|
13 |
SSB switch_input |
- |
Passenger outside handle antenna(+)_output |
|
14 |
Driver handle antenna switch_input |
Rear center seat belt indicator_output |
Immobilizer K-Line |
|
15 |
P-Position_input (PWM) |
Fuel door open relay_output |
Bumper antenna (+)_output |
|
- |
|||
|
16 |
Fog switch_input |
- |
Interior antenna2(+)_output |
|
17 |
Light switch_input |
Auto light sensor signal_input |
IGN2_input |
|
18 |
Front wiper INT volume switch_input |
Auto light sensor power_output |
IGN1_input |
|
19 |
Multifunction switch_input |
ATM solenoid_output |
IGN2 relay_output |
|
20 |
Assist mirror unfolding switch_oupout |
Puddle pocket lamp_output |
Battery_power |
|
21 |
Assist mirror (Horizontal)_output |
- |
Brake switch_input |
|
22 |
Front washer switch_input |
SSB ring illumination_output |
Start feedback_input |
|
23 |
Front wiper low switch_Input |
piezo buzzer_output |
- |
|
24 |
LIN1 (PDW) |
SSB symbol illumination_output |
Driver outside handle antenna (-)_output |
|
25 |
LIN2 (Safety ECU) |
Fuel door close relay_output |
Interior1 (-)_output |
|
26 |
LIN3 (Rain sensor) |
Wiper power relay_output |
Front bumper antenna (-)_output |
|
27 |
PDW-R power_input |
Rear seat belt indicator RH_output |
Passenger outside handle antenna (-)_output |
|
28 |
PDW_input |
Rear seat belt indicator LH_output |
ESCL COM |
|
29 |
SSB switch1_input |
3rd line sheet belt indicator LH_output |
Tailgate3 antenna(-) |
|
30 |
ESCL unlock_input |
Rear wiper relay_output |
ESCL Enable_output |
|
31 |
Passenger outside handle switch_input |
Auto light sensor ground_output |
Bumper antenna (-)_output |
|
32 |
PDW switch_input |
Wiper parking switch_input |
Interior antenna2 (-)_output |
|
33 |
Sun roof Status_input |
|
ACC_input |
|
34 |
Head lamp switch(High)_input |
Mirror power_input |
|
|
35 |
Front wiper switch_input |
ACC relay_output |
|
|
36 |
Rear wiper switch_input |
Battery (+)_ECU |
|
|
37 |
Assist mirror folding _output |
|
|
|
38 |
Assist mirror (Vertical)_output |
Smart Key. Repair procedures
Smart Key
Smart Key Code Saving
1.
Connect the DLC cable of diagnostic tool to the data link connector
(16 pins) in driver side crash pad lower panel, turn the power on diagnostic
tool...
Categories
- Manuals Home
- 4th Generation Santa Fe Owners Manual
- 4th Generation Santa Fe Service Manual
- Rear Occupant Alert (ROA)
- Engine Control System
- Instrument panel overview
- New on site
- Most important about car
Power adjustment
The front seat can be adjusted by using the control switches located on the outside of the seat cushion. Before driving, adjust the seat to the proper position so that you can easily control the steering wheel, foot pedals and controls on the instrument panel.
WARNING
NEVER allow children in the vehicle unattended. The power seats are operable when the vehicle is turned off.
Copyright © 2024 www.hsafe4.com