Hyundai Santa Fe: SRSCM / SRS Control Module (SRSCM). Repair procedures

Hyundai Santa Fe (TM) 2019-2025 Service Manual / Restraint / SRSCM / SRS Control Module (SRSCM). Repair procedures

Removal
1.
Turn the engine OFF.
2.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
3.
Remove the floor console assembly.
(Refer to Body - "Floor Console Assembly")
4.
Loosen the mounting bolts and then remove the air duct.
5.
Pull up the lock of the SRSCM connector to disconnect the connector.

6.
Remove the SRSCM mounting bolts and then remove the SRSCM.
  
You must remove or install the SRSCM or other SRS components with the ignition switch OFF to avoid accidental airbag deployment.

Installation
1.
Turn the engine OFF.
2.
Disconnect the battery negative cable and wait for at least three minutes before beginning work.
3.
Install the SRSCM with the SRSCM mounting bolts (3EA).
Tightening torque :
10.8 - 12.7 N.m (1.0 - 1.3 kgf.m, 7.2 - 9.4 lb-ft)

4.
Connect the SRSCM harness connector.
5.
Install the rear air duct.
6.
Install the floor console assembly.
(Refer to Body - "Floor Console Assembly")
7.
Reconnect the battery negative cable.
8.
After installing the SRSCM, confirm proper system operation :
Turn the ignition switch ON; the SRS indicator light should be turned on for about six seconds and then go off.
  
If the SRSCM is replaced always, perform variant coding. Also, perform the lateral G sensor 0 point setup.
(Refer to Brake System - "Yaw-rate and Lateral G Sensor")
Variant Coding
After replacing the SRSCM with a new one, the "Variant Coding" procedure must be performed.
Variant Coding Procedure
1.
Connect the cable of GDS to the data link connector in driver side crash pad lower panel, and turn on the GDS.
2.
Select the 'S/W Management' and 'Car model'.

3.
Select "Airbag" and "ACU/SRSCM Variant Coding".

4.
Perform the "ACU/SRSCM Variant Coding" procedure according to the GDS screen message.

    SRS Control Module (SRSCM). Schematic diagrams

    ..

    Front Impact Sensor (FIS). Description and operation

    Description The front impact sensor (FIS) is installed in the Front End Module (FEM). They are remote sensors that detect acceleration due to a collision at its mounting location...

    Other information:

    Hyundai Santa Fe (TM) 2019-2025 Service Manual: Desctiprion and operation


    Description ADAS_PRK is a unit that controls the functions required for ADAS parking. If the ADAS_PRK is applied, the parking distance warning function is also controlled by the ADAS_PRK. System Function Parking Collision-Avoidance Assist (PCA) PCA is a parking safety system that assists in collision warning and emergency braking in the event of a collision with rear pedestrians and obstacles during reversing at low speed (collision warning is displayed on the instrument cluster and monitor and audible warning sounds) Remote Smart Parking Assist (RSPA) The Remote Smart Parking Assist (RSPA) uses the vehicle sensors to search the parking space...

    Hyundai Santa Fe (TM) 2019-2025 Owner's Manual: Forward/Reverse Parking Distance Warning (PDW)


    Forward/Reverse Parking Distance Warning will help warn the driver if an obstacle is detected within a certain distance when the vehicle is moving forward or in reverse at low speeds. Detecting sensor [1] : Front ultrasonic sensors, [2] : Rear ultrasonic sensors Refer to the picture above for the detailed location of the detecting sensors...

    Categories

    Engine oil pressure warning light. Low fuel level warning light

    Engine oil pressure warning light

    This warning light illuminates:

    When the engine oil pressure is low.

    If the engine oil pressure is low:

    1. Drive carefully to the nearest safe location and stop your vehicle.

    2. Turn the engine off and check the engine oil level (For more details, refer to “Engine Oil” section in chapter 9). If the level is low, add oil as required.

    read more


     
    Copyright © 2025 www.hsafe4.com