Hyundai Santa Fe: Charging System / Troubleshooting

Hyundai Santa Fe (TM) 2019-2024 Service Manual / Engine Electrical System / Charging System / Troubleshooting

Troubleshooting
  
Be careful not to short-circuit the wiring by the body or other wirings.
In case of discharging problem, measure dark current at all times.
(Charging System - "Dark Current Inspection").
When checking the alternator main fuse, perform continuity test and voltage test between terminals as well as visual check to confirm normal operation.
When checking the ground, repair or replace after inspecting for defective ground cable, defective installation or defective contact due to foreign object.
It is not recommended to use non-authentic parts as installing non-authentic parts may cause malfunction of charging system.
Be careful as misassembly may cause short-circuit of wiring, which may result in battery discharge.
As it will reset and appear as normal if the battery negative (-) terminal is disconnected while measuring dark current, measure by using a hook meter without disconnecting the negative (-) terminal.
Note that there may be various phenomenons / possible causes / repair measures apart from above.
For more effective repairs, refer to DTC guide and ETM.
Symptom
Suspected Area
Remedy
Charging warning lamp does not turn on during IG ON.
Broken alternator main fuse
Inspect / Repair / Replace fuse.
Broken instrument cluster fuse
Inspect / Repair / Replace fuse.
Broken instrument cluster internal bulb
Inspect / Repair / Replace instrument cluster.
Defective connection of wiring connector
Inspect / Repair / Replace wiring connection.
Defective voltage regulator or alternator
Inspect / Repair / Replace voltage regulator or alternator.
Defective connection of battery terminal
Inspect tightening of (+) and (-) battery terminals to specified torque.
Communication error
Inspect wiring between regulator and ECM.
Inspect transmission signal of ECM.
Inspect / Repair / Replace alternator if the wiring and ECM are normal.
Charging warning lamp does not turn off during engine running.
Worn drive belt or lack of tension
Inspect / Repair / Replace drive belt.
Defective connection, corroded or worn battery cable
Inspect connection of battery cable and Inspect / Repair / Replace cable.
Broken alternator main fuse
Inspect / Replace alternator main fuse or battery cable.
Defective voltage regulator or alternator
Inspect / Replace voltage regulator or alternator.
Defective wiring
Inspect / Replace wiring.
Defective instrument cluster
Inspect / Replace instrument cluster
Slip in alternator pulley
Inspect / Replace alternator pulley.
Adjust tension / Replace drive belt.
Defective connection of battery terminal
Inspect tightening of (+) and (-) battery terminals to specified torque.
Charging warning lamp turns on.
Slip, worn or lack of tension in drive belt
Adjust tension / Replace drive belt.
Inspect / Replace auto tensioner (only for auto tensioner type).
Error in Alternator Management System (AMS) voltage
Inspect battery sensor connecting harness and connection with body.
Error in battery sensor
Inspect / Repair / Replace battery sensor.
Short between battery sensor wiring and body
Inspect / Repair / Replace battery sensor.
Defective alternator L terminal output power
Inspect / Repair / Replace alternator or regulator.
Degradation due to defective contact of battery (+) terminal
Check tightening to specified torque / Inspect / Repair / Replace battery wiring.
Short in alternator connecting extension connector internal pin
Inspect / Repair / Replace wiring.

Short circuit between body and mission ground
Inspect / Repair / Replace ground.
Communication error
Inspect / Repair / Replace wiring between regulator and ECM.
Inspect transmission signal of ECM.
Inspect / Repair / Replace alternator if wiring and ECM are normal.
Short in the middle of connection to alternator L terminal
(L terminal applied vehicle model)
Inspect / Repair / Replace wiring.
Drive belt rotation stops due to slip in crankshaft damper pulley or defective pulley.
Inspect or replace crankshaft damper pulley / Inspect, repair or replace drive belt tensioner bearing.
Slip, worn or lack of tension in drive belt
Adjust tension / Inspect / Repair / Replace drive belt.
Defective voltage regulator
Inspect / Repair / Replace voltage regulator.
Defective alternator
Inspect / Repair / Replace alternator.
Broken alternator main fuse
Inspect / Repair / Replace alternator main fuse or battery wiring cable.
Defective ground
Inspect / Repair / Replace ground.
Discharged battery
Adjust tension / Inspect / Repair / Replace drive belt.
Inspect / Repair / Replace wiring connection.
Inspect / Repair / Replace alternator main fuse.
Inspect / Repair / Replace alternator.
Inspect / Repair / Replace voltage regulator.
Inspect / Repair / Replace battery unit.
Inspect for dark current / Repair / Replace.
Learn / Inspect / Repair / Replace battery sensor.
Inspect for short / Repair / Replace battery cable.
Inspect / Repair / Replace ECM.
Inspect / Repair / Replace body electrical related parts.
Inspect / Repair / Replace installation status of alternator connector.
Inspect / Repair / Replace tightening of (+) and (-) battery terminals to specified torque.
Swollen battery
Defective battery
Inspect / Replace battery.
Defective voltage regulator or alternator
Inspect / Repair / Replace voltage regulator or alternator.
Defective charging related parts or wiring
Inspect / Repair / Replace charging related parts and wiring.
After inspection, repair or replace related parts in case of malfunction.

    Components and components location

    Components 1. ECM 2. Battery 3. Alternator 4. Starter 5. Instrument Cluster 6. Ignition switch or start/stop button 7...

    Schematic diagrams

    ..

    Other information:

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Mechanism Rail. Repair procedures


    Replacement 1. Remove the roof trim. 2. Remove the movable glass. (Panorama sunroof - refer "Movable Glass") 3. Remove the roller blind...

    Hyundai Santa Fe (TM) 2019-2024 Service Manual: Troubleshooting


    Trouble Symptom Charts Trouble Symptom 1 Trouble Symptom 2 Trouble symptom Probable cause Remedy The set vehicle speed varies greatly upward or downward "Surging" (repeated alternating acceleration and deceleration) occurs after setting Malfunction of the vehicle speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of ECM Check input and output signals at ECM Trouble Symptom 3 Trouble symptom Probable cause Remedy The CC system is not canceled when the brake pedal is depressed Damaged or disconnected wiring of the brake pedal switch Repair the harness or replace the brake pedal switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 4 Trouble symptom Probable cause Remedy The CC system is not canceled when the shift lever is moved to the "N" position (It is canceled, however, when the brake pedal is depressed) Damaged or disconnected wiring of inhibitor switch input circuit Repair the harness or repair or replace the inhibitor switch Improper adjustment of inhibitor switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 5 Trouble symptom Probable cause Remedy Cannot decelerate (coast) by using the "SET/–" switch Temporary damaged or disconnected wiring of "SET/–" switch input circuit Repair the harness or replace the "SET/–" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 6 Trouble symptom Probable cause Remedy Cannot accelerate or resume speed by using the "RES/+" switch Damaged or disconnected wiring, or short circuit, or "RES/+" switch input circuit Repair the harness or replace the "RES/+" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 7 Trouble symptom Probable cause Remedy CC system can be set while driving at a vehicle speed of less than 40km/h (25mph), or there is no automatic cancellation at that speed Malfunction of the vehicle-speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 8 Trouble symptom Probable cause Remedy The cruise main switch indicator lamp does not illuminate (But CC system is normal) Damaged or disconnected bulb of cruise main switch indicator lamp Repair the harness or replace the part...

    Categories

    Engine oil pressure warning light. Low fuel level warning light

    Engine oil pressure warning light

    This warning light illuminates:

    When the engine oil pressure is low.

    If the engine oil pressure is low:

    1. Drive carefully to the nearest safe location and stop your vehicle.

    2. Turn the engine off and check the engine oil level (For more details, refer to “Engine Oil” section in chapter 9). If the level is low, add oil as required.

    read more


     
    Copyright © 2024 www.hsafe4.com