Hyundai Santa Fe: Fender / Repair procedures

Hyundai Santa Fe (TM) 2019-2025 Service Manual / Body (Interior and Exterior) / Fender / Repair procedures

Replacement

•	When removing the fender, wrap protective tape around a screwdriver or remover not to damage components

•	Put on gloves to prevent hand injuries

•	When removing the clips, use a clip remover.

1.	Remove the front bumper. (Refer to Front Bumper - "Front Bumper Assembly")

2.	Loosen the mounting screws and then remove the front bumper side mounting bracket (A).

3.	Remove the fender side cover (A).

4.	Remove the DRL (Daytime Running Lights) assembly. (Refer to Body Electrical System - "DRL (Daytime Running Lights)")

5.	Remove the front wheel guard. (Refer to Body Side Molding - "Front Wheel Guard")

6.	Remove the fender garnish. (Refer to Body Side Molding - "Fender Garnish.")

7.	Using a screwdriver or remover, remove the delta garnish (A).

Loosen the mounting bolts remove the fender assembly (A).

Tightening torque :

(B) : 7.7 - 11.6 N.m (0.8 - 1.2 kgf.m, 5.8 - 8.7 lb-ft)

To install, reverse removal procedure.

•	Replace any damaged clips (or pin-type retainers).

Components and components location

Hood

Other information:

Hyundai Santa Fe (TM) 2019-2025 Service Manual: Battery. Description and operation

Description AGM Battery AGM battery is used for especially heavy load on the vehicle network depending on equipment and requirements. AGM stands for Absorbent Glass Material Battery; that is absorbent glass fibre fleece. AGM batteries are fitted in models with electrical loads/consumers which have a high energy demand...

Hyundai Santa Fe (TM) 2019-2025 Service Manual: Troubleshooting

Trouble Symptom Charts Trouble Symptom 1 Trouble Symptom 2 Trouble symptom Probable cause Remedy The set vehicle speed varies greatly upward or downward "Surging" (repeated alternating acceleration and deceleration) occurs after setting Malfunction of the vehicle speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of ECM Check input and output signals at ECM Trouble Symptom 3 Trouble symptom Probable cause Remedy The CC system is not canceled when the brake pedal is depressed Damaged or disconnected wiring of the brake pedal switch Repair the harness or replace the brake pedal switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 4 Trouble symptom Probable cause Remedy The CC system is not canceled when the shift lever is moved to the "N" position (It is canceled, however, when the brake pedal is depressed) Damaged or disconnected wiring of inhibitor switch input circuit Repair the harness or repair or replace the inhibitor switch Improper adjustment of inhibitor switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 5 Trouble symptom Probable cause Remedy Cannot decelerate (coast) by using the "SET/–" switch Temporary damaged or disconnected wiring of "SET/–" switch input circuit Repair the harness or replace the "SET/–" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 6 Trouble symptom Probable cause Remedy Cannot accelerate or resume speed by using the "RES/+" switch Damaged or disconnected wiring, or short circuit, or "RES/+" switch input circuit Repair the harness or replace the "RES/+" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 7 Trouble symptom Probable cause Remedy CC system can be set while driving at a vehicle speed of less than 40km/h (25mph), or there is no automatic cancellation at that speed Malfunction of the vehicle-speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 8 Trouble symptom Probable cause Remedy The cruise main switch indicator lamp does not illuminate (But CC system is normal) Damaged or disconnected bulb of cruise main switch indicator lamp Repair the harness or replace the part...