Hyundai Santa Fe: Propeller Shaft Assembly / Repair procedures
| •
|
Be careful not to damage the parts located under the vehicle
(floor under cover, fuel filter, fuel tank and canister) when
raising the vehicle using the lift.
(Refer to General Information - "Lift and Support Points")
|
|
|
1. |
After making a match mark on the flange yoke and transaxle companion,
remove the propeller shaft mounting bolts (A).
|
Tightening torque :
53.9 - 68.6 N.m (5.5 - 7.0 kgf.m, 39.8 - 50.6 lb-ft)
|
|
• |
Use a hexagon socket to prevent damage to the head when
removing and installing bolts.
|
|
• |
Mark the location and direction of bolt and washer before
removing the propeller shaft.
|
|
• |
Installing the bolt and washer differently from the
initial state can result in unbalanced propeller shaft
causing abnormal vibration of propeller shaft at high
speed.
|
|
• |
If abnormal vibration and noise occur at high vehicle
speeds after replacing propeller shaft with a new one,
balance the propeller shaft with a balancing machine.
|
|
• |
The bolt is a special bolt applied with bond, so do
not reuse.
|
|
|
|
2. |
Remove the bracket (A) after loosening the mounting bolts.
|
|
3. |
Loosen the center bearing bracket mounting bolts (A).
|
Tightening torque :
53.9 - 68.6 N.m (5.5 - 7.0 kgf.m, 39.8 - 50.6 lb-ft)
|
|
• |
Mark the location and direction of bolt and washer before
removing the propeller shaft.
|
|
• |
Installing the bolt and washer differently from the
initial state can result in unbalanced propeller shaft
causing abnormal vibration of propeller shaft at high
speed.
|
|
|
|
4. |
After making a match mark on the constant velocity joint and rear differential
companion, remove the propeller shaft mounting bolts (A).
|
Tightening torque :
53.9 - 68.6 N.m (5.5 - 7.0 kgf.m, 39.8 - 50.6 lb-ft)
|
|
• |
Use a hexagon socket to prevent damage to the head when
removing and installing bolts.
|
|
• |
Mark the location and direction of bolt and washer before
removing the propeller shaft.
|
|
• |
Installing the bolt and washer differently from the
initial state can result in unbalanced propeller shaft
causing abnormal vibration of propeller shaft at high
speed.
|
|
• |
If abnormal vibration and noise occur at high vehicle
speeds after replacing propeller shaft with a new one,
balance the propeller shaft with a balancing machine.
|
|
• |
The bolt is a special bolt applied with bond, so do
not reuse.
|
|
|
|
1. |
To install, reverse the removal procedures.
|
Other information:
Vehicle Stability Management is a function of the Electronic Stability Control
(ESC) system. It helps the vehicle stay stable when accelerating or braking suddenly
on wet, slippery and rough roads where traction over the four tires can suddenly
become uneven...
..
Categories
WARNING
To reduce the risk of an air bag deploying unexpectedly and causing serious
injury or death:
Do not hit or allow any objects to impact the locations where air
bags or sensors are installed.
Do not perform maintenance on or around the air bag sensors. If
the location or angle of the sensors is altered, the air bags may deploy when
they should not or may not deploy when they should.
Installing bumper guards with nongenuine Hyundai or non-equivalent
parts may adversely affect the collision and airbag deployment performance.
Press the Engine Start/Stop button to the OFF or ACC position and
wait for 3 minutes when the vehicle is being towed to prevent inadvertent air
bag deployment.
Have all air bag repairs performed by an authorized HYUNDAI dealer.
read more
